本試劑盒應用雙抗體夾心法測定標本中兔基質金屬蛋白酶-9（MMP-9）水平。用純化的兔基質金屬蛋白酶-9（MMP-9）抗體包被微孔板，制成固相抗體，往包被單抗的微孔中依次加入基質金屬蛋白酶-9（MMP-9），再與HRP標記的基質金屬蛋白酶-9（MMP-9）抗體結合，形成抗體-抗原-酶標抗體復合物，經過徹底洗滌后加底物TMB顯色。TMB在HRP酶的催化下轉化成藍色，并在酸的作用下轉化成終的黃色。顏色的深淺和樣品中的基質金屬蛋白酶-9（MMP-9）呈正相關。用酶標儀在450nm波長下測定吸光度（OD值），通過標準曲線計算樣品中兔基質金屬蛋白酶-9（MMP-9）濃度。

試劑盒組成

1	30倍濃縮洗滌液	20ml×1瓶	7	終止液	6ml×1瓶
2	酶標試劑	6ml×1瓶	8	標準品（160μg/L）	0.5ml×1瓶
3	酶標包被板	12孔×8條	9	標準品稀釋液	1.5ml×1瓶
4	樣品稀釋液	6ml×1瓶	10	說明書	1份
5	顯色劑A液	6ml×1瓶	11	封板膜	2張
6	顯色劑B液	6ml×1/瓶	12	密封袋	1個

標本要求

1．標本采集后盡早進行提取，提取按相關文獻進行，提取后應盡快進行實驗。若不能馬上進行試驗，可將標本放于-20℃保存，但應避免反復凍融

2．不能檢測含NaN3的樣品，因NaN3抑制辣根過氧化物酶的（HRP）活性。

操作步驟

1. 標準品的稀釋：本試劑盒提供原倍標準品一支，用戶可按照下列圖表在小試管中進行稀釋。

80μg/L	5號標準品	150μl的原倍標準品加入150μl標準品稀釋液
40μg/L	4號標準品	150μl的5號標準品加入150μl標準品稀釋液
20μg/L	3號標準品	150μl的4號標準品加入150μl標準品稀釋液
10μg/L	2號標準品	150μl的3號標準品加入150μl標準品稀釋液
5μg/L	1號標準品	150μl的2號標準品加入150μl標準品稀釋液

2. 加樣：分別設空白孔（空白對照孔不加樣品及酶標試劑，其余各步操作相同）、標準孔、待測樣品孔。在酶標包被板上標準品準確加樣50μl，待測樣品孔中先加樣品稀釋液40μl，然后再加待測樣品10μl（樣品終稀釋度為5倍）。加樣將樣品加于酶標板孔底部，盡量不觸及孔壁，輕輕晃動混勻。

3. 溫育：用封板膜封板后置37℃溫育30分鐘。

4. 配液：將30倍濃縮洗滌液用蒸餾水30倍稀釋后備用

5. 洗滌：小心揭掉封板膜，棄去液體，甩干，每孔加滿洗滌液，靜置30秒后棄去，如此重復5次，拍干。

6. 加酶：每孔加入酶標試劑50μl，空白孔除外。

7. 溫育：操作同3。

8. 洗滌：操作同5。

9. 顯色：每孔先加入顯色劑A50μl，再加入顯色劑B50μl，輕輕震蕩混勻，37℃避光顯色15分鐘.

10. 終止：每孔加終止液50μl，終止反應（此時藍色立轉黃色）。

11. 測定：以空白空調零，450nm波長依序測量各孔的吸光度（OD值）。測定應在加終止液后15分鐘以內進行。

計算

以標準物的濃度為橫坐標，OD值為縱坐標，在坐標紙上繪出標準曲線，根據樣品的OD值由標準曲線查出相應的濃度；再乘以稀釋倍數；或用標準物的濃度與OD值計算出標準曲線的直線回歸方程式，將樣品的OD值代入方程式，計算出樣品濃度，再乘以稀釋倍數，即為樣品的實際濃度。

注意事項

1．試劑盒從冷藏環境中取出應在室溫平衡15-30分鐘后方可使用，酶標包被板開封后如未用完，板條應裝入密封袋中保存。

2．濃洗滌液可能會有結晶析出，稀釋時可在水浴中加溫助溶，洗滌時不影響結果。

3．各步加樣均應使用加樣器，并經常校對其準確性，以避免試驗誤差。一次加樣時間好控制在5分鐘內，如標本數量多，推薦使用排槍加樣。

4．請每次測定的同時做標準曲線，好做復孔。如標本中待測物質含量過高（樣本OD值大于標準品孔第一孔的OD值），請先用樣品稀釋液稀釋一定倍數（n倍）后再測定，計算時請后乘以總稀釋倍數（×n×5）。

5．封板膜只限一次性使用，以避免交叉污染。

6．底物請避光保存。

7．嚴格按照說明書的操作進行，試驗結果判定必須以酶標儀讀數為準.

8．所有樣品，洗滌液和各種廢棄物都應按傳染物處理。

9．本試劑不同批號組分不得混用。

10. 如與英文說明書有異，以英文說明書為準。

保存條件及有效期

1．試劑盒保存：；2-8℃。

2．有效期：6個月

Human MMP-9

FOR RESEARCH USE ONLY

Assay range：45μg/L -1200μg/L 96 determinations

Purpose

This kit allows for the determination of MMP-9 concentrations in Human serum, cell culture supernates and other biological fluids

Principle of the assay

The kit assay Human MMP-9 level in the sample，use Purified Human MMP-9 antibody to coat microtiter plate wells, make solid-phase antibody, then add MMP-9 to wells, Combined MMP-9 antibody which With HRP labeled goat anti-Human become antibody - antigen - enzyme-antibody complex, after washing Completely, Add TMB substrate solution,TMB substrate becomes blue color At HRP enzyme-catalyzed, reaction is terminated by the addition of a sulphuric acid solution and the color change is measured spectrophotometrically at a wavelength of 450 nm. The concentration of Human MMP-9 in the samples is then determined by comparing the O.D. of the samples to the standard curve.

Materials provided with the kit

1	wash solution	20ml×1bottle	7	Stopp Solution	6ml×1 bottle
2	HRP-Conjugate reagent	6ml×1 bottle	8	Standard（2400μg/L）	0.5ml×1 bottle
3	Microelisa stripplate	12well×8strips	9	Standard diluent	1.5ml×1bottle
4	Sample diluent	6ml×1 bottle	10	Instruction	1
5	Chromogen Solution A	6ml×1 bottle	11	Closure plate membrane	2
6	Chromogen Solution B	6ml×1 bottle	12	Sealed bags	1

Specimen requirements

1. extract as soon as possible after Specimen collection,and according to the relevant literature, and should be experiment as soon as possible after the extraction. If it can’t, specimen can be kept in -20 ℃ to preserve, Avoid repeated freeze-thaw cycles.

2. Can’t detect the sample which contain NaN3, because NaN3 inhibits HRP active.

Assay procedure

1. Dilute and add sample:Dilute Original density Standard as follow table:

1200μg/L	5 Standard	150μl Original density Standard+150μl Standard diluent
600μg/L	4 Standard	150μl 5 Standard+150μl Standard diluent
300μg/L	3 Standard	150μl 4 Standard+150μl Standard diluent
150μg/L	2 Standard	150μl 3 Standard +150μl Standard diluent
75μg/L	1 Standard	150μl 2 Standard +150μl Standard diluent

2.add sample：Set blank wells separately (blank comparison wells don’t add sample and HRP-Conjugate reagent, other each step operation is same). testing sample well. add Sample dilution 40μl to testing sample well, then add testing sample 10μl (sample final dilution is 5-fold), add sample to wells , don’t touch the well wall as far as possible, and Gently mix.

3.Incubate: After closing plate with Closure plate membrane ,incubate for 30 min at 37℃.

4.Configurate liquid: 30-fold (or 20-fold) wash solution diluted 30-fold (or 20-fold) with distilled water and reserve.

5.washing：Uncover Closure plate membrane, discard Liquid, dry by swing, add washing buffer to every well, still for 30s then drain, repeat 5 times, dry by pat.

6.add enzyme：Add HRP-Conjugate reagent 50μl to each well, except blank well.

7.incubate：Operation with 3.

8.washing：Operation with 5.

9.color：Add Chromogen Solution A 50ul and Chromogen Solution B to each well, evade the light preservation for 15 min at 37℃

10.Stop the reaction：Add Stop Solution50μl to each well, Stop the reaction(the blue color change to yellow color).

11.assay：take blank well as zero , Read absorbance at 450nm after Adding Stop Solution and within 15min.

Steps description

Standard, Sample diluent

Add Standard, Sample diluent, incubate for 30 min at 37℃.

Wash 5 time,Add HRP-Conjugate reagent, incubate for 30 min at 37℃.

Wash 5 times,Add Chromogen Solution A and B, incubate for 30 min at 37℃.

Add Stopp Solution

Read absorbance at 450nm within 15 min

calculate

Calculate

Take the standard density as the horizontal, the OD value for the vertical ,draw the standard curve on graph paper, Find out the corresponding density according to the sample OD value by the Sample curve, multiplied by the dilution multiple, or calculate the straight line regression equation of the standard curve with the standard density and the OD value ,with the sample OD value in the equation, calculate the sample density, multiplied by the dilution factor, the result is the sample actual density.

Important notes

1. The kit takes out from the refrigeration environment should be balanced 15-30 minutes in the room temperature, ELISA plates coated if has not use up after opened, the plate should be stored in Sealed bag.

2. washing buffer will Crystallization separation, it can be heated the water helps dissolve when dilute . Washing does not affect the result.

3. add Sample with sampler Each step, And proofread its accuracy frequently, avoids the experimental error. add sample within 5 min, if the number of sample is much , recommend to use Volley .

4. if the testing material content is excessively higher (The sample OD is bigger than the first standard well ),please dilute Sample (n-fold), Please diluente and multiplied by the dilution factor.（×n×5）.